|
|
|
Transformers |
TAS1907-01 Model
Miniature Active AC Current Transformers
|
1.Features:
- Input is AC current signal, output is AC voltage signal;
- Operation amplifier is built-in inside, high accuracy of measurement is obtained;
- Completely sealed, strong mechanical and environmental endurance, strong
dielectric strength, safe and reliable to use;
- Elegant outline, light and small in structure, being able to be directly
soldered on PCB.
2.Ambient Conditions
- Ambient temperature: -55...+85°C;
- Relative humid <90% при 40°C;
- Atmospheric pressure: 860~1060mbar (650~800mmHg approximately);
3.Range of working Frequency: 20Hz~10kHz
4.Insulation Rating: Class F (155°C).
5.Safety features:
- Dielectric resistance: >1000MOm in normal condition;
- Insulation withstand voltages: 2000V 50Hz/1min;
- Fire retardancy: In conformity with UL94-Vo
6.Outline Drawing, Installation Dimension (shown as Fig. 1 below) and Function
of Pins
Pin No. |
2-4 |
6 |
7 |
8 |
9 |
10 |
Function |
input |
+B |
adjusting |
G |
-B |
output |
7. Technical parameters:
Model |
Rated
input
current
(virtual
value) |
Rated
output
voltage
(virtual
value) |
Phase
Shift |
Non
Linearity |
Insulating
Withstand
Voltage |
Working
Power
Supply |
TVS1907-01 |
5A
(Pin 2-4) |
5V
(Pin 8-10) |
<30` |
<0.3% |
>2000V |
±15V~22V |
8.Application Instructions:
- The input coil between Pin 2 and Pin 4 must be connected in series with the
loop of the measured current circuit, Pin 6 connected to +B. Pin 9 connected to
–B. Pin 8 connected to ground. Pin10 is the output terminal. Pin7 is the adjusting
terminal.
- While input AC current moving between 0~5A, output of 0~5V between Pin10
and Pin 8 is obtained and is linearly correspondent.
- Phase shift can be compensated by connecting a capacitor between Pin 7 and
Pin 10 and compensated to <15’ when choosing a capacitor of 0.033μF
- Output voltage can be changed by connecting a resistor between Pin 7 and
Pin 10 and it will be as bellow if the resistor connected is R and input rated
voltage:
9.Attention
- Pin 8 must be connected to ground, otherwise the accuracy will be influenced;
- If want to change output AC signal to DC signal, the method of absolute value
rectifying can be applied to carry out. Otherwise, as the tube voltage drop of
diode exists, the linear correspondence will be damaged;
- Increasing working voltage between Pin 6 and Pin 9 can extend scope of measuring,
contrariwise it will reduce the scope;
- If the output and input parameters are not suitable for you, we can make
it as request.
|
|
|
|
|
- Цены, опубликованные в Магазине, могут не являться окончательными и предназначены только для предварительного ознакомления.
Информацию о наличии товаров и свежих ценах уточняйте у менеджеров, они устанавливают окончательные цены при оформлении заказа в зависимости от количества товара и истории клиента. Или нажмите ссылку:
sales@dart.ru
- Представленная техническая информация и размеры на чертежах, опубликованных на сайте, носят справочный характер и не предназначены для использования в конструкторской документации без согласования с нами.
Для получения актуализированной технической информации нажмите ссылку:
alex@dart.ru
- Возможность поставки товаров, где не указан код товара, уточняйте у наших менеджеров.
- Перед закладкой компонентов в серийные изделия необходимо запрашивать образцы!
|
|
|
|
|